Hello,
after having played mainly with plant surfaces over the last months I tried my first insect stack today. An ant portrait. While I am ok technically with the result it nearly drove me crazy to mount the ant on a needle.
It was freshly killed and I could not get it sticking on a needle in a way that I could nicely portrait it. Filnally - completely exhausted and frustrated from many trials ad several ants being covered in glue I took the scalpel and chopped off the head. I needled it from the back of the head.
While it sort of worked I am absolutely not happy with the procedure...there must be more effective ways...?
How do you mount insects, mainly to shoot portraits?
All the best
Andreas
Mounting question
Moderators: rjlittlefield, ChrisR, Chris S., Pau
- rjlittlefield
- Site Admin
- Posts: 23626
- Joined: Tue Aug 01, 2006 8:34 am
- Location: Richland, Washington State, USA
- Contact:
Re: Mounting question
To produce the image that you did -- an isolated head surrounded by uniform background -- the procedure that you eventually followed was probably the best way to solve the problem.Andreas Wistuba wrote:Finally ... I took the scalpel and chopped off the head. I needled it from the back of the head.
I understand your frustration. Isolating small bits can be infuriatingly difficult. But as far as I know, needles and glue are still the main methods. They get quite a lot easier if you can work under a low power stereo microscope.
Perhaps other people can offer better alternatives.
--Rik
-
- Posts: 318
- Joined: Thu Sep 22, 2011 9:55 am
- Location: Florida
Other than needles, there is also point mounting. You just take a piece of sturdy paper, and cut an appropriate sized triangle. Then glue the specimen to the tip of the paper. Here is an illustration http://extension.entm.purdue.edu/401Boo ... ll_insects
Personally I have switched to point mounting from just raw pins. I find it much easier to set the specimen upside down, put a tiny dab a adhesive onto the tip of paper, and rest the point down onto he specimen till it dries. So long as you are careful you should be able to avoid getting the mount in most images.
Personally I have switched to point mounting from just raw pins. I find it much easier to set the specimen upside down, put a tiny dab a adhesive onto the tip of paper, and rest the point down onto he specimen till it dries. So long as you are careful you should be able to avoid getting the mount in most images.
-
- Posts: 9
- Joined: Fri Jun 22, 2007 9:54 am
https://www.youtube.com/watch?v=OpyNnh1w0_g
The link above is to a youtube video that includes a view of me mounting a bug. That starts at time 2:38 and runs for about a minute.
I darken a toothpick with a black magic marker. I place the bug on a clean plastic (disposable) surface. I moisten the tip of the toothpick with super glue. I use the "gel" type with a bit higher viscosity as it dries more quickly and does not run or wick where it does not belong. I then bring the tip of the toothpick with the glue to the bug and carefully touch the legs. With the small flies I photograph, I can easily ensnare 3-4 legs in the glue. The surface tension of the glue usually pulls the legs to be parallel with the toothpick. I allow the glue to dry for a few seconds, occasionally puffing gently with some warm breath on the joint to aid in drying. I then check the mounted insect under my dissecting scope to look for dust, lint or other imperfections in the bug's appearance that can be easily remedied. Then off to the camera...
Hope this helps!
Keith
The link above is to a youtube video that includes a view of me mounting a bug. That starts at time 2:38 and runs for about a minute.
I darken a toothpick with a black magic marker. I place the bug on a clean plastic (disposable) surface. I moisten the tip of the toothpick with super glue. I use the "gel" type with a bit higher viscosity as it dries more quickly and does not run or wick where it does not belong. I then bring the tip of the toothpick with the glue to the bug and carefully touch the legs. With the small flies I photograph, I can easily ensnare 3-4 legs in the glue. The surface tension of the glue usually pulls the legs to be parallel with the toothpick. I allow the glue to dry for a few seconds, occasionally puffing gently with some warm breath on the joint to aid in drying. I then check the mounted insect under my dissecting scope to look for dust, lint or other imperfections in the bug's appearance that can be easily remedied. Then off to the camera...
Hope this helps!
Keith