newbie question: connecting microscope optics to cannon 400d
Moderators: rjlittlefield, ChrisR, Chris S., Pau
newbie question: connecting microscope optics to cannon 400d
hi all, apologies if the questions below have been answered before but after checking the FAQ's and many many threads here i coudnt find the answer i was looking for, this is probably down to my lack of knowledge in the subject.
i have been into macro photography for some time, i currently reverse mount to get the images i have over at fickr but i want to get closer still.
i have a canon eos 400d and want to use microsope lenses attached to the camera to get closer images (like lord v and many others here) as time goes on i suppose i would
like to get a microscope but thats for another time.
the question i have is connecting the microscope optics to the camera and which are the best optics to buy, i have searched but have so far been unable to find an answer is there anything available for canon to attach these microscope optics to the camera?
i have been into macro photography for some time, i currently reverse mount to get the images i have over at fickr but i want to get closer still.
i have a canon eos 400d and want to use microsope lenses attached to the camera to get closer images (like lord v and many others here) as time goes on i suppose i would
like to get a microscope but thats for another time.
the question i have is connecting the microscope optics to the camera and which are the best optics to buy, i have searched but have so far been unable to find an answer is there anything available for canon to attach these microscope optics to the camera?
- rjlittlefield
- Site Admin
- Posts: 23621
- Joined: Tue Aug 01, 2006 8:34 am
- Location: Richland, Washington State, USA
- Contact:
olympus 10x m10
this is just a handheld shot of a quarter
this is just a handheld shot of a quarter
Last edited by SONYNUT on Sun Jan 23, 2011 4:38 pm, edited 1 time in total.
..............................................................................
Just shoot it......
Just shoot it......
thanks sonynut,
rjlittlefield - i think my difficulty was not realising when i was given the information i needed, unfortunately after reading 40-60 posts (and there are some long posts) the information kind of gets muddled up.
i have since found some of the information i needed thanks to guys like sonynut and my own perusing of the site and posts you have here.
rjlittlefield - i think my difficulty was not realising when i was given the information i needed, unfortunately after reading 40-60 posts (and there are some long posts) the information kind of gets muddled up.
i have since found some of the information i needed thanks to guys like sonynut and my own perusing of the site and posts you have here.
- rjlittlefield
- Site Admin
- Posts: 23621
- Joined: Tue Aug 01, 2006 8:34 am
- Location: Richland, Washington State, USA
- Contact:
- Craig Gerard
- Posts: 2877
- Joined: Sat May 01, 2010 1:51 am
- Location: Australia
In the meantime......Rik wrote:Your question is now appearing often enough that it really ought to be covered in the FAQs. I'll get that done later today. Stay tuned...
You can try just about any microscope objective; but whether it provides good images is another matter.
Short story:
Many microscope objectives were/are dependent on secondary CA correction via the microscope eyepieces. When those objectives are used on their own, as a lense on a DSLR, significant issues with Chromatic Aberration arise.
Some objectives, such as the finite Nikon CF Plan, BD Plan objectives were designed to correct for CA within the actual objective. These are better suited for use as 'macro' lenses. 'Plan' objectives also provide a more uniform FOV across the entire frame.
Finite microscope objectives have a designated 'tubelength' inscribed on the barrel, for example, 160/- or 210/0. Those numbers (minus 10mm) indicate how far from the sensor or film plane the shoulder of the objective should ideally be located to produce the designated magnification. Finite objectives do not like to be used too far way from their designated magnification.
Various objectives have different thread sizes. Most (but not all) finite objectives have RMS threads.
As far as adapters are concerned for attaching an RMS threaded objective to your Canon DSLR. Here are a few examples of the components. This particular seller provides a good service and stocks many helpful adapters for using microscope objectives for macro photography.
EOS to M42 adapter:
http://cgi.ebay.com/AF-confirm-M42-adap ... 0418311542
RMS to M42:
http://cgi.ebay.com/RMS-Thread-M42-Adap ... 0470968028
RMS Thread to M42 'Cone' Adapter:
http://cgi.ebay.com.au/RMS-Thread-M42-A ... 0352400700
Also read the discusion:http://www.photomacrography.net/forum/v ... hp?t=10661
And then there are the infinity-corrected objectives.....stay tuned, I'm sure they will be addressed in Rik's forthcoming FAQ.
Craig
To use a classic quote from 'Antz' - "I almost know exactly what I'm doing!"